不同粒径改性粉煤灰对磷酸根吸附性能的影响

废水排放过量的磷导致水体污染日益严重，将粉煤灰通过化学改性制备成了水化硅酸钙吸附剂，研究了改性吸附剂对磷酸根的吸附效果。利用XRD, SEM及BET比表面积等手段对粒度分级前后的吸附剂进行表征，研究不同粒级吸附剂对磷酸根的吸附性能，并考察其吸附机理。结果表明，不同粒级的吸附剂其化学成分出现了明显的偏析现象，孔隙结构也差异显著。相比其他粒径下的吸附剂颗粒，颗粒粒径在50?75 μm时，吸附剂中钙和硅含量较多，铝、铁和镁含量较低，水化硅酸钙组分含量最高，且伴有含铝的托贝莫来石晶体出现，钙离子的增加使其可以与更多的磷酸根结合形成沉淀。同时此粒径下具有较高的比表面积及孔隙度，疏松多孔的结构为钙离子提供更多活性位点。当使用粒径在50?75 μm的吸附剂吸附磷酸根时，磷的饱和吸附量可达到17.1 mg/g，比未分级的吸附剂高19.58%。     

Coupling in situ experiments and modeling – Opportunities for data fusion,machine learning,and discovery of emergent behavior

This paper reviews recent studies, that not only includes both experiments and modeling components, but celebrates a close coupling between these techniques, in order to provide insights into the plasticity and failure of polycrystalline metals. Examples are provided of studies across multiple-scales, including, but not limited to, density functional theory combined with atom probe tomography, molecular dynamics combined with in situ transmission electron miscopy, discrete dislocation dynamics combined with nanopillars experiments, crystal plasticity combined with digital image correlation, and crystal plasticity combined with in situ high energy X-ray diffraction. The close synergy between in situ experiments and modeling provides new opportunities for model calibration, verification, and validation, by providing direct means of comparison, thus removing aspects of epistemic uncertainty in the approach. Further, data fusion between in situ experimental and model-based data, along with data driven approaches, provides a paradigm shift for determining the emergent behavior of deformation and failure, which is the foundation that underpins the mechanical behavior of polycrystalline materials.     

Theoretical study of a thermoelectric-assisted vapor compression cycle for air-source heat pump applications

This paper proposes a thermoelectric-assisted vapor compression cycle (TVCC) for applications in air-source heat pump systems which could enhance the heating capacity of the system. Performances of TVCC are calculated and then compared with that of basic vapor compression cycle (BVCC). The simulation results show that when coefficients of performance (COPs) of the two cycles are almost equal, the TVCC under maximum COP condition of the thermoelectric modules still performs better than BVCC by 13.0% in heating capacity through selecting the appropriate intermediate temperature. In addition, the TVCC can also achieve an improvement of 16.4%–21.7% in both the heating COP and capacity when compared with the BVCC with an assistant electric heater that is provided with the equivalent power input of thermoelectric heat exchanger. Thus, the TVCC could be beneficial to the applications in small heat pumps if there is always need for auxiliary electric heat.     

以用户为中心的可见光通信协作传输中训练资源分配算法

以用户为中心的可见光通信协作传输是近年来出现的新架构,这导致虚拟小区之间出现重叠。为避免导频污染问题,每个虚拟小区中的光接入点(AP)或者虚拟小区中选择相同AP的用户发送的训练序列应该是正交的。针对可见光通信中以用户为中心的协作网络,研究训练资源的正交分配问题,提出了一种新的导频分配算法,联合导频分配和用户选择问题,以期最大限度地增加虚拟小区内可被接入的用户数。分析和仿真结果表明,该导频分配方案可以有效改善导频污染问题,提高训练资源利用率,并且相比已有的导频分配方案,性能有所改进。     

Additively manufactured respirators: quantifying particle transmission and identifying system-level challenges for improving filtration efficiency

The COVID-19 pandemic has disrupted the supply chain for personal protective equipment (PPE) for medical professionals, including N95-type respiratory protective masks. To address this shortage, many have looked to the agility and accessibility of additive manufacturing (AM) systems to provide a democratized, decentralized solution to producing respirators with equivalent protection for last-resort measures. However, there are concerns about the viability and safety in deploying this localized download, print, and wear strategy due to a lack of commensurate quality assurance processes. Many open-source respirator designs for AM indicate that they do not provide N95-equivalent protection (filtering 95% of SARS-CoV-2 particles) because they have either not passed aerosol generation tests or not been tested. Few studies have quantified particle transmission through respirator designs outside of the filter medium. This is concerning because several polymer-based AM processes produce porous parts, and inherent process variation between printers and materials also threaten the integrity of tolerances and seals within the printed respirator assembly. No study has isolated these failure mechanisms specifically for respirators. The goal of this paper is to measure particle transmission through printed respirators of different designs, materials, and AM processes. The authors compare the performance of printed respirators to N95 respirators and cloth masks. Respirators in this study printed using desktop- and industrial-scale fused filament fabrication processes and industrial-scale powder bed fusion processes were not sufficiently reliable for widespread distribution and local production of N95-type respiratory protection. Even while assuming a perfect seal between the respirator and the user’s face, although a few respirators provided >90% efficiency at the 100−300 nm particle range, almost all printed respirators provided <60% filtration efficiency. Post-processing procedures including cleaning, sealing surfaces, and reinforcing the filter cap seal generally improved performance, but the printed respirators showed similar performance to various cloth masks. The authors further explore the process-driven aspects leading to low filtration efficiency. Although the design/printer/material combination dictates the AM respirator performance, the identified failure modes originate from system-level constraints and are therefore generalizable across multiple AM processes. Quantifying the limitations of AM in producing N95-type respiratory protective masks advances understanding of AM systems toward the development of better part and machine designs to meet the needs of reliable, functional, end-use parts.     

增效过磷酸钙的增效机制及其对玉米生长的影响

利用猪毛、风化煤和腐植酸钠的水解液为增效剂制备了一种增效过磷酸钙,探讨了增效过磷酸钙的增效机制及其对玉米生长的影响。结果表明,蒸馏水浸提条件下,增效过磷酸钙能减缓水溶磷的释放,具备较高的pH值缓冲性。与普通过磷酸钙相比,增效过磷酸钙处理的玉米生物量平均增加了41.9%,吸磷量和吸钙量分别增加了61.7%和27.8%,根系活力增加了24.3%。该研究结果对过磷酸钙生产的技术改进具有指导意义。     

An approach to measure infill matric suction of irregular infilled rock joints under constant normal stiffness shearing

Rock joints infilled with sediments can strongly influence the strength of rock mass. As infilled joints often exist under unsaturated condition, this study investigated the influence of matric suction of infill on the overall joint shear strength. A novel technique that allows direct measurement of matric suction of infill using high capacity tensiometers (HCTs) during direct shear of infilled joints under constant normal stiffness (CNS) is described. The CNS apparatus was modified to accommodate the HCT and the procedure is explained in detail. Joint specimens were simulated by gypsum plaster using three-dimensional (3D) printed surface moulds, and filled with kaolin and sand mixture prepared at different water contents. Shear behaviours of both planar infilled joints and rough joints having joint roughness coefficients (JRCs) of 8–10 and 18–20 with the ratios of infill thickness to asperity height (t/a) equal to 0.5 were investigated. Matric suction shows predominantly unimodal behaviour during shearing of both planar and rough joints, which is closely associated with the variation of unloading rate and volumetric changes of the infill material. As expected, two-peak behaviour was observed for the rough joints and both peaks increased with the increase of infill matric suction. The results suggest that the contribution of matric suction of infill on the joint peak normalised shear stress is relatively independent of the joint roughness.     

Estimation of the Stress-Strength Reliability for Exponentiated Pareto Distribution Using Median and Ranked Set Sampling Methods

In reliability analysis, the stress-strength model is often used to describe the life of a component which has a random strength (X) and is subjected to a random stress (Y). In this paper, we considered the problem of estimating the reliability R=P [Y<X] when the distributions of both stress and strength are independent and follow exponentiated Pareto distribution. The maximum likelihood estimator of the stress strength reliability is calculated under simple random sample, ranked set sampling and median ranked set sampling methods. Four different reliability estimators under median ranked set sampling are derived. Two estimators are obtained when both strength and stress have an odd or an even set size. The two other estimators are obtained when the strength has an odd size and the stress has an even set size and vice versa. The performances of the suggested estimators are compared with their competitors under simple random sample via a simulation study. The simulation study revealed that the stress strength reliability estimates based on ranked set sampling and median ranked set sampling are more efficient than their competitors via simple random sample. In general, the stress strength reliability estimates based on median ranked set sampling are smaller than the corresponding estimates under ranked set sampling and simple random sample methods.     

园区多能互补供能系统设计方法研究

为提高园区多能互补工程的能源综合利用效率及整体效益，对供能系统设计中的负荷统计、逐时负荷匹配、供能系统、设备选型、容量配置及运行策略等问题进行了分析和总结，提出园区多能互补供能系统设计的基本流程与方法，可为园区多能互补供能系统的设计提供参考。